Eris Accent BT Setup: Wireless Streaming to Studio Monitors

Quick answer

To set up your Eris Accent BT speakers for wireless streaming, power them on, put them in Bluetooth pairing mode, and connect from your phone, tablet, or computer. Keep the speakers within a few feet during pairing, then place them on a stable surface at ear level. The entire process takes about two minutes.

Before you start: what you need

Unbox both speakers and identify the active speaker (the one with the power jack and control knobs). Place it on a stable surface where you can reach the rear panel. The passive speaker connects to the active one with the included speaker wire. You'll also need a power outlet and your Bluetooth source device. No additional cables are required for wireless streaming, but keep the speaker wire handy for the initial hookup.

Step 1: Connect the speakers and power on

Connect the passive speaker to the active speaker using the supplied speaker wire. Plug the active speaker into a wall outlet and turn the power switch on. The front LED should light up. If it doesn't, check that the outlet works and the power cable is fully seated. A common mistake is forgetting to connect the speaker wire before powering on, which results in no sound from the passive speaker.

Step 2: Enter Bluetooth pairing mode

Press and hold the Bluetooth button on the active speaker until the LED blinks rapidly. This indicates pairing mode. On some devices, you may need to press the button once to wake it, then hold to pair. If the LED doesn't blink, try holding the button longer or check that the speaker isn't already connected to another device. The Eris Accent BT does not have a dedicated pairing button on the remote, so use the top panel control.

Step 3: Pair from your device

Open Bluetooth settings on your phone, tablet, or computer. Select 'Eris Accent BT' from the list of available devices. If you don't see it, make sure the speaker is still in pairing mode and within 3 feet. Once paired, the LED will stop blinking and stay lit. You can now stream audio wirelessly. For computers, you may need to set the Eris Accent BT as the default playback device in your sound settings.

Step 4: Fine-tune the sound

Use the low- and high-frequency adjustment knobs on the rear panel to tailor the sound to your room. If the speakers are on a desk near a wall, reducing the low frequencies can prevent boominess. For a more accurate response, start with both knobs at the center detent and adjust gradually. Remember that these settings affect all inputs, not just Bluetooth.

Troubleshooting common Bluetooth issues

If you experience dropouts, move your device closer to the speakers and ensure there are no obstructions like walls or metal objects between them. Interference from Wi-Fi routers or microwaves can also cause stuttering. If the speaker won't pair, turn it off and on again, then repeat the pairing steps. For persistent problems, check that your device's Bluetooth is enabled and that the speaker isn't already connected to another device. The Eris Accent BT does not support multipoint pairing, so it can only connect to one device at a time.

Setup steps at a glance

1. Connect the speakers: Link the passive speaker to the active one with the supplied speaker wire, then plug in and power on the active speaker. Checkpoint: The power LED should light up. If not, verify the outlet and cable connections.
2. Enter pairing mode: Press and hold the Bluetooth button on the active speaker until the LED blinks rapidly. Checkpoint: If the LED doesn't blink, hold the button longer or ensure the speaker isn't already connected to another device.
3. Pair from your device: Select 'Eris Accent BT' in your device's Bluetooth settings. Keep the device within 3 feet during pairing. Checkpoint: The LED stops blinking and stays lit when paired successfully.
4. Adjust the sound: Use the rear-panel low- and high-frequency knobs to tune the response to your room. Checkpoint: Start with knobs at center detent and adjust gradually to avoid overcorrecting.
5. Troubleshoot dropouts: Move your device closer, remove obstructions, and avoid interference from Wi-Fi routers or microwaves. Checkpoint: If issues persist, power-cycle the speaker and re-pair. Remember it only connects to one device at a time.

Product facts

• Eris® Accent BT (Pair): Eris Accent BT bookshelf speakers deliver 60W of onboard Class D power, with low- and high-frequency adjustment knobs for fine-tuning. These speakers are loud enough for a room and let you tailor the sound to your space, which is useful when streaming from different sources.
• Eris® 3.5BT 2nd Gen (Pair): Eris 3.5BT 2nd Gen monitors offer 25 watts per side and are available in multiple colors. If you need a more compact option for a bedroom studio or gaming setup, these provide studio-quality sound with a smaller footprint.